The main goal with the master thesis has been to do a status evaluation of the chain machinery with its start chain and wire to secure the production on a short basis due to that a reconstruction is not planned at this time. An evaluation of the condition of the start chain and the rollers in the chain depository has been done. An offer has been requested for a new start chain and the evaluation of the start chains may be a basis for the decision taking. The production has been able to go on, although it has arisen some problems which have been difficult to find the causes for. There is no gathered ?picture? of the machinery status and a mapping of each machinery has been compiled of comprehensive logs.

The producers of grain in Sweden are facing a rough future. The competition is getting harder all the time, in Sweden, in EU and also from the ?world market?. The producers have to be more efficient and have to have bigger units. Many producers might have to look for new alternative production opportunities.

This graduation work is a result of implementing Lean Production using OEE and SMED at Enics Sweden AB in Malmö. Enics doesn?t have an established improvement concept and therefore should this work serve as an introduction to possibly start with Lean Production. A result in this report is that an OEE value has been identified within a common order at Enics. Other results are that an implementation of a Lean-board has been implemented and furthermore, within SMED, a flag that indicates changeover..

The saw blade producer, Håkansson Sågblad AB, patented in the U.S. a new blade profiledesigned specially to cut fish and meat. The most important advantage of that blade is that its teethare not set, therefore the material lost when cutting is really smaller. The special geometry of thatprofile made that nobody had found a proper way to produce it before.The goal of the outlined work is to develop a machine to produce these new blades in afeasible way.The research approach of the project can roughly be divided into three phases:1.- Invention and development of a proper distribution of blades to produce a big amount ofthem at the same time.2.- Research of the best production process to produce the blades.3.- Main design of the machine to produce the blades.In the Thesis these three points are carefully developed and studied in the form of the startpoint of a really bigger project. Some tests had been done in order to prove all the analytical ideasand the results obtained had been satisfactory enough to give Håkansson the start point of a bigbusiness.

During year 2004 Ålö AB made significant change in their production process. The production of front loaders is nowadays highly automated with short operation times. To be able to control their process in a better way Ålö recently decided that they needed a tool for simulation of their production and to shift patterns. This final thesis started with a pilot study in Ålö?s factory in Brännland.

 The sawmill industry is a relative fragmented industry that is in an economic upswing andwith a hard competition. The customers have high demands on their suppliers and the highcustomer demand make it necessary for the companies to make a streamlining in planningand production. For that reason it is very important that the planning- and productionprocesses aren?t to complex and with a simple structure.The purpose of this report is to study and map out a marked out part of a planning- andproduction process, from adjust works to final delivery, at a company in the sawmill industry.Different methods have been used for the report, among others interviews and subordinatedmaterial.We have mapped out a marked out part of the planning- and production process at theCompany. This part we have studied, and we have analysed the process it self and otherthings connected to the process.We see the planning- and production process in the Company as complex.

Lean Production is used by many manufacturing companies. Companies in process industries do not use Lean Production to the same extent today. This is part of the report's issue to explore how Lean Production can be applied to a company in the process industries.The investigated company is a processing company that manufactures various types of foil. The company wishes to streamline its production and has therefore asked the authors to examine if Lean Production can offer the company improvements in their production. Lean Production value stream mapping tool has been selected to identify and analyze the current state of two of its products in production.

This study includes a life cycle assessment, LCA, on an ecological produced cotton shirt for the company Reflective Circle, which designs ethical and ecological clothes.Initially were cotton farming and textile production studied to gather basic knowledge about the processes. Since this shirt is being ecological produced in the whole production chain, we studied what an ecological production means, but also how a conventional production works. When this was done we could start to discuss the differences and similarities between the production of the shirt and general conventional production.When the LCA was first initiated, the main focus was on the green house gas emissions from the manure at the cultivation. Thereafter the process steps such as picking, ginning, carding, spinning, weaving and sewing were being studied. The picking is done by hand, but the rest of the processes are handed by machines which consumes energy.

Syftet med uppsatsen är att studera huruvida start-up hightech bolag tillämpar klassisk förvärvsteori och att undersöka ifall och hur fusions- och förvärvsprocessen skiljer sig mellan dessa bolag och vad teorin visar på..

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS production costs is possible. .

 The sawmill industry is a relative fragmented industry that is in an economic upswing andwith a hard competition. The customers have high demands on their suppliers and the highcustomer demand make it necessary for the companies to make a streamlining in planningand production. For that reason it is very important that the planning- and productionprocesses aren?t to complex and with a simple structure.The purpose of this report is to study and map out a marked out part of a planning- andproduction process, from adjust works to final delivery, at a company in the sawmill industry.Different methods have been used for the report, among others interviews and subordinatedmaterial.We have mapped out a marked out part of the planning- and production process at theCompany. This part we have studied, and we have analysed the process it self and otherthings connected to the process.We see the planning- and production process in the Company as complex.

The aim of this study is to examine the factors that motivate people to seek employment at a start-up company. We have conducted a qualitative study by interviewing ten people at six different start-up companies in Stockholm. Empirical findings show that the interviewed are mainly motivated by the possibility to work with challenging work tasks and the possibility to influence and acquire responsibility. Furthermore, status and other self-fulfilment factors such as building something from scratch that can create value and the possibility for a potential ownership is also contributing to the interviewed motivation to seek employment at a start-up. Factors such as an attractive labour market and a possibility to take a temporary break from the university, have contributed to the overall low risk perception of working at a start-up company.

This report contains results of our study at CTC in Ljungby. CTC produces heating products such as boilers, heat pumps and additional products to their heating systems.The purpose of the report is to make a proposal how CTC will supply their new production line for heat pumps with materials. The proposal includes a production layout and a scheme for how to place the material in the production storage.The new production line will produce two different products and both of them have several variants. The line will also have a mixed flow, so the products can be produced in a random order. These conditions demand that the production line has great flexibility and that the material to all the variants can be stored in the production storage.With these conditions as input we made a layout proposal to the company.

The aim of this thesis was to use qualitative approaches to show how four preschool teachers experienced their start in the profession as a preschool teacher. The questions in the stydy were as follows: What kind of expectations did the preshool teachers have before the start in the profession? What did the preshool teachers experience as difficulty and opportunity at the start in the profession? How do they think now about their professional development during the early period in the profession? The empirical material, I got through a qualitative interview method. My theoretical starting point was to take the hermeneutic research perspective, aimed for interpreting and understanding. Theories of Socialization and socialization for teachers, socio-cultural theories and theories of tacit knowledge have been used to analyze the material.

Saab Training Systems (STS) in Huskvarna is manufacturing material for educationalpurposes to armies worldwide. They are now implementing parts of the Lean productionconcept in their organisation.One part of the work with Lean production is to eliminate waste. To be able to identify waste,value stream mapping is a good tool and also what we used in our thesis. To gain a betterefficiency in the production of Personnel Detector Device (PDD) flow was one of our goals.The PDD is a harness used during battle training which registers if the user is being hit by itsenemy.Our work with the thesis started up with a short education in Lean production and in valuestream mapping (VSM). The work proceeded with a VSM of the production flow of the PDD,interviews were made and studies of literature were done to gain greater knowledge of thesubject and solve the task.The VSM resulted in five areas which were followed up out of those six we identified.